My profile & Contact	Tweet

Attack on titan(shingeki no kyojin)
How to make "3d maneuver gear"(Rittai kidou souti) (with templates)
Comic version
Vol.3 tank and anchor part


Return to Vol.2 (sheath part)

Attention in the work
-When you uses a thing including the thinner(Bond, lacquer thinner etc) or spray, make good ventilation.
And wear a gas mask.


-When you toast mterials etc, make good ventilation.
And don't breathe smoke, don't put smoke in your eyes.

-When you dig mterials etc with Soldering iron, make good ventilation.
And don't breathe in smoke, don't put smoke in your eyes.

-Don't use fire near the things which are easy to burn such as paint, thinner etc.

-When you finished using tools, pull an outlet.

-Read labels of materials and tools, and understand how to use.

How to make templates
Make Templates from "Kousakuyousi"(one of hard paper in Japan).
Pattern paper is here.
When you want to know how to make Templates, browse this page.



How to build
Make the body part.
Cut material into the Templates form.
Cut out 5mm thick EVA foam.
The alphabets in photo is name of templates.


**********************************************************************

EVA foam is a soft material.
You can process it easily.
Another name is EVA board, EVA zote, Craft foam etc.
I usually use one called "Lion board".
"Lion board" is sold only in Japan.

Watch video.

**********************************************************************

-------------------------------------------------------------------------------------------------------
【5mm厚COSボードをキャラヌノで買う】


【COSボードを楽天で買う】

-------------------------------------------------------------------------------------------------------
【5mm厚コスプレボードをAmazonで買う】


【コスプレボードを楽天で買う】

-------------------------------------------------------------------------------------------------------

**********************************************************************

Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

When you cut, put EVA foam on Cutting mat.
Don't cut in the air, while holding by hand.
Break a b blade frequentry, if you feel sharpness of using blade became bad.
If you want to do work more speedy, use "Running fire box cutter","Blade breaker".
"Running fire box cutter" can have 6 pieces blade inside.
"Blade breaker" can break easy and speedy.


Use Art knife PRO for small ornaments etc.

**********************************************************************

Glue with a Liquid super glue.
When you use a Super glue Accelerator, Hardening speed becomes fast.
(Smoke may be generated. Don't breathe in the smoke and don't put in eyes.)


**********************************************************************


Super glue can glue a large surfaces easily.
But it can't glue a small surface such as this photo well


Then you should use a following spray.
I always use this.
Watch video.


Super glue accelerator
This can glue surfaces in several seconds.
When you use 100ml, you can make a armorset or about three weapons.
←100ml ←180ml ←420ml

About super glue
I use general liquid super glue.

**********************************************************************

Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Make rivets with a Hot melt(glue gun).



Cut the cord.


Cut out 1.5mm or 2mm thick EVA foam.


-------------------------------------------------------------------------------------------------------
【1.5mm厚COSボードをキャラヌノで買う】


【COSボードを楽天で買う】

-------------------------------------------------------------------------------------------------------
【1.5mm厚コスプレボードをAmazonで買う】


【コスプレボードを楽天で買う】

-------------------------------------------------------------------------------------------------------

Glue with a Hot melt(glue gun).


Make a break with a Box cutter.


Put Velcro between the break.
Glue Velcro with "Bond G17"(one of liqud glue in Japan) or a Hot melt(glue gun).



Glue with a Hot melt(glue gun).


Make the ring form parts.
Cutting with Box cutter is also good, but Using Prick punch is better.
Cut 1.5mm or 2mm thick EVA foam into a circle form with a Prick punch.
Make a ring by cutting it with a small Prick punch.

←手で押しこむだけでお手軽なタイプ←ハンマーで叩くタイプ

Cut material into the Templates form.
Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Liquid super glue.


Fill it up with a Hot melt(glue gun).


Glue with a Liquid super glue.


Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Liquid super glue.


Make the lid.
Cut material into the Templates form.
Cut out 5mm thick EVA foam.


You must use a tool for cutting out a fair circle. Details are here.



Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Hot melt(glue gun).


Glue with a Liquid super glue.


Remove the corner by toasting with a Lighter.(Don't breathe in the smoke, be careful about fire)

←ガス充填式ライターとガスボンベを使うとお得

I finished toasting.


Make the anchor.
Make Templates from "Kousakuyousi"(one of hard paper in Japan).
Pattern paper is here.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.
Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Liquid super glue.


Bend by heating with a Lighter or a Heat gun.(Be careful about fire)



Glue with a Liquid super glue.


I finished glueing.


Shave the corner with a Box cutter.


Remove the corner by toasting with a Lighter.(Don't breathe in the smoke, be careful about fire)


Glue with a Liquid super glue.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


I finished glueing.


Cut the cord.


Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Hot melt(glue gun).


Glue with a Hot melt(glue gun).


Make the frame part.
Cut material into the Templates form.
Cut out 5mm thick EVA foam.
Cut out 10mm thick EVA foam.


-------------------------------------------------------------------------------------------------------
【10mm厚COSボードをキャラヌノで買う】


【COSボードを楽天で買う】

-------------------------------------------------------------------------------------------------------
【10mm厚コスプレボードをAmazonで買う】


【コスプレボードを楽天で買う】

-------------------------------------------------------------------------------------------------------

Glue with a Liquid super glue.


Glue with a Liquid super glue.


Shave the corner with a Box cutter.


Remove the corner by toasting with a Lighter.(Don't breathe in the smoke, be careful about fire)


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Paste Synthetic leather as reinforce.(Because this part is bended along the belt well. To make sure.)
Glue with a Liquid super glue.

PUストレッチレザー 生地 無地 全52色 黄 オレンジ 赤 ピンク 青系 17色布幅130cm 50cm以上10cm単位販売 価格：176円（税込、送料別) (2019/1/23時点)

ソフトエナメル 生地 無地 42色 モノトーン、ゴールド・シルバー系 全42色 布幅130cm 50cm以上10cm単位販売 価格：188円（税込、送料別) (2019/1/23時点)

I finished glueing.


Cut material into the Templates form.
Cut out 10mm thick EVA foam.


Glue with a Liquid super glue.
Make a break with a Box cutter.
(Surrounded part by red circle)
Glue with a Hot melt(glue gun).


Make a gap with a Box cutter.


Glue with a Hot melt(glue gun).


Glue Velcro with "Bond G17"(one of liqud glue in Japan) or a Hot melt(glue gun).


Make a gap with a Box cutter.


Glue Velcro with "Bond G17"(one of liqud glue in Japan) or a Hot melt(glue gun).


Paset the mate Velcro to the tank side.
Glue Velcro with "Bond G17"(one of liqud glue in Japan) or a Hot melt(glue gun). Detailes are here.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.


Cut material into the Templates form.
Cut out 10mm thick EVA foam.


Make a hole with a Box cutter.
A Box cutter is used for cutting.(Big blade is easier to use.)
Art knife PRO is better for such as this small hole.


Cut the cord.


Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Hot melt(glue gun).


Glue with a Hot melt(glue gun).


Make a gap with a Box cutter.


Glue Velcro with "Bond G17"(one of liqud glue in Japan) or a Hot melt(glue gun).


I finished glueing.


About fitting method of the tank.
Cut Velcro.


Glue with a Hot melt(glue gun).


Tie the tank and plate part of back side with Velcro


Stick the tank's Velcro and the frame's Velcro.


I finished attaching.


If there is not the plate of back side, use this method.
Cut Synthetic leather.


Glue with a Hot melt(glue gun).


Fit a safety pin.
Glue with a Hot melt(glue gun).


Fit your cloth with the safety pin.


To be continued vol.4(painting part)

Please
I'm making Yotube videos.
Please watch them and please subscribe my YouTube channel.
These are new videos.
































Return to Top page