EVA foam is soft material.
You can process it easily.
Other names are EVA board, EVA zote, Craft foam etc.
Cosplayers all over the world use this.
It's sold in Amazon or AliExpress etc.

Introduction video




Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

I always use "Running fire box cutter","Blade breaker",Cutting mat.
"Blade breaker" can break the blade easily.


Use Standard art knife or Cushion grip art knife to cut small ornaments etc, too.
Standard art kinfe is for 1.5mm thickness and 3mm thickness.
Cushion grip art knife is for 5mm thickness and 10mm thickness.

●1.5mm厚コスプレボードを楽天で買う

コスプレボード　白1.5mm×660mm×1000mm 価格：605円（税込、送料別) (2019/10/23時点)

コスプレボード　黒1.5mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：660円（税込、送料別) (2019/10/23時点)

コスプレボードシール　白1.5mm×660mm×500mm 接着剤不要のシール接着、装飾等に 価格：594円（税込、送料別) (2019/10/23時点)

コスプレボードシール　黒1.5mm×660mm×500mm 接着剤不要のシール接着、装飾等に 価格：682円（税込、送料別) (2019/10/23時点)

●1.5mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 2mm厚 白 価格：620円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 2mm厚 白 価格：1,000円（税込、送料別) (2023/5/25時点)

COSボード匠 Lサイズ 2mm厚 白 価格：4,000円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 2mm厚 黒 価格：620円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 2mm厚 黒 価格：1,000円（税込、送料別) (2023/5/25時点)

Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)



I finished glueing.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.

●5mm厚コスプレボードを楽天で買う

コスプレボード 白5mm×660mm×500mm 価格：517円（税込、送料別) (2019/10/23時点)

コスプレボード 白5mm×660mm×1000mm 価格：990円（税込、送料別) (2019/10/23時点)

コスプレボード　白5mm×1000mm×2000mm 価格：3564円（税込、送料別) (2019/10/23時点)

コスプレボード　黒5mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：1320円（税込、送料別) (2019/10/23時点)

コスプレボード　黒5mm×1000mm×2000mm 黒だから裏塗り処理を省略出来る 価格：4180円（税込、送料別) (2019/10/23時点)

●5mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 5mm厚 白 価格：880円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 5mm厚 白 価格：1,560円（税込、送料別) (2023/5/25時点)

COSボード匠 Lサイズ 5mm厚 白 価格：5,300円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 5mm厚 黒 価格：880円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 5mm厚 黒 価格：1,560円（税込、送料別) (2023/5/25時点)

Mark holes on the Templates.


I finished marking.


Cut material into the Templates form.
Cut out 3mm thick EVA foam.





3mm厚コスプレボードを楽天で買う

コスプレボード 白3mm×660mm×500mm 価格：418円（税込、送料別) (2019/10/23時点)

コスプレボード　白3mm×660mm×1000mm 価格：693円（税込、送料別) (2019/10/23時点)

コスプレボード　白3mm×1000mm×2000mm 価格：2464円（税込、送料別) (2019/10/23時点)

コスプレボード 黒3mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：990円（税込、送料別) (2019/10/23時点)

コスプレボードシール　白3mm×660mm×500mm 接着剤不要のシール接着、装飾等に 価格：726円（税込、送料別) (2019/10/23時点)

●3mm厚コスプレボードをAmazonで買う

Glue with a Liquid super glue.
When you use a Super glue Accelerator, Hardening speed becomes fast.
(Smoke may be generated. Don't breathe in the smoke and don't put in eyes.)





Super glue accelerator makes hardening time short.
It's so useful.
Watch this video.


When you use 100ml, you can make a armorset or about two, three weapons.
←100ml ←420ml


Glue with a Liquid super glue.


I finished glueing.


Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 10mm thick EVA foam.

●10mm厚コスプレボードを楽天で買う

コスプレボード 白10mm×660mm×500mm 価格：880円（税込、送料別) (2019/10/23時点)

コスプレボード　白10mm×660mm×1000mm 価格：1540円（税込、送料別) (2019/10/23時点)

コスプレボード　黒10mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：2486円（税込、送料別) (2019/10/23時点)

●10mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 10mm厚 白 価格：1,400円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 10mm厚 白 価格：2,490円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 10mm厚 黒 価格：1,400円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 10mm厚 黒 価格：2,490円（税込、送料別) (2023/5/25時点)

Round off the corners with a Box cutter etc.


Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 3mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


I finished glueing.


Make the edges smooth with a Soldering iron (Don't breathe in the smoke, be careful a burn).
Or, cut it by edged tools.
(Actually I used fire, but it's dangerous method. I recommend a Soldering iron
If accedents happens, it's self-responsibility)


Building the big blade


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Make the big blade.
Mark holes on the Templates.


Mark holes on the Templates.


Turn it over.
Mark holes on the Templates.


I finished marking.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.
The symbols in photo are parts name of templates.


Make hole with a Drill or a Pinvice.



I finised making a hole.


Glue with a Liquid super glue.


I finished glueing.


Use a Aluminum stick.
You can substitute various metalic sticks.
Cut it into appropriate length with Nippers.


I finished cutting.


Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 10mm thick EVA foam.
The symbols in photo are parts name of templates.

●10mm厚コスプレボードを楽天で買う

コスプレボード 白10mm×660mm×500mm 価格：880円（税込、送料別) (2019/10/23時点)

コスプレボード　白10mm×660mm×1000mm 価格：1540円（税込、送料別) (2019/10/23時点)

コスプレボード　黒10mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：2486円（税込、送料別) (2019/10/23時点)

●10mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 10mm厚 白 価格：1,400円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 10mm厚 白 価格：2,490円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 10mm厚 黒 価格：1,400円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 10mm厚 黒 価格：2,490円（税込、送料別) (2023/5/25時点)

Make a gap with a Box cutter etc.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.
The symbols in photo are parts name of templates.


Glue with a Liquid super glue.


Round off the corners with a Box cutter etc.


Glue with a Liquid super glue.


I finished glueing.


Heap a Hot melt(glue gun) for reinforcement.


ギャクヨガが愛用しているグルーガンです、口が広くてとても使いやすい！

Glue with a Liquid super glue.


I finished glueing.


Cut 1.5mm or 2mm thick EVA foam thin.


Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 1.5mm or 2mm thick EVA foam.


Glue with a Liquid super glue.


Make the edges smooth with a Soldering iron (Don't breathe in the smoke, be careful a burn).
Or, cut it by edged tools.
(Actually I used fire, but it's dangerous method. I recommend a Soldering iron
If accedents happens, it's self-responsibility)


Carve the pattern with a Soldering iron.
(Don't breathe in the smoke and don't put in eyes. If accedents happens, it's self-responsibility.)


ギャクヨガが使っているハンダゴテです、コテ台付き。

Cut material into the Templates form.
Cut out 3mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


I finished glueing.


Cut "Kousakuyousi"(one of hard paper in Japan) into a belt form.


Put "Kousakuyousi"(one of hard paper in Japan) side by side.


Paste them



"Kousakuyousi"(one of hard paper in Japan) is sold in only Japan.
It's harder than Drawing paper. The thickness is about 0.5mm.
I'm sure you can't get it.
Then, substitute various thin plastic sheets.


Cut out "Kousakuyousi"(one of hard paper in Japan).


Mark holes on the Templates.


I finished marking.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.
Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.
Glue with a Liquid super glue.


I finished glueing.


Glue with a Liquid super glue.


I finished glueing.


Heap a Hot melt(glue gun) for reinforcement.


Glue with a Liquid super glue.


I finished glueing.


Glue edges of the blade.
Glue with "Bond G17"(one of sticky glue in Japan). Detailed process is here.
Paint it with a broken piece of "Kousakuyousi"(one of hard paper in Japan) as a brush.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.



Reinforce the blade by applying Liquid super glue on the edge.


Glue with a Hot melt(glue gun).


Building the small blades


Cut out "Kousakuyousi"(one of hard paper in Japan).


Use a Aluminum stick.
You can substitute various metalic sticks.
Cut it into appropriate length with Nippers.


I finished cutting.


Glue with a Hot melt(glue gun).


I finished glueing.


Glue with a Hot melt(glue gun).


Glue edges of the blade.
Glue with "Bond G17"(one of sticky glue in Japan). Detailed process is here.
Paint it with a broken piece of "Kousakuyousi"(one of hard paper in Japan) as a brush.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.


Cut material into the Templates form.
Cut out 3mm thick EVA foam.


Heat it by Heat gun or Steam iron. Bend it and keep the form.
(Actually I used fire, but it's dangerous method. I recommend Heat gun or Steam iron.
If accedents happens, it's self-responsibility)


Glue with a Liquid super glue.


I finished glueing.


Present state.



Please follow and subscribe
Please follow my Facebook & twitter!


Please subscribe my channel!


Painting
Stand the cylinder form parts with a wood struck big nails.


Begin painting.
At first, paint undercoat on EVA foam.
The effects are as follows.

-Color becomes well.
-It becomes hard to come off.
-Gloss comes out well.
-You can save quantity of the paint.


1.Gesso
This is easy.

【Merit】
-It's usable just to paint with a paint brush.
-Gesso don't contain thinner, then you can use it in the room.
-You can use also Acrylic paint.
-There are several colors one, white black etc.

【Demerit】
-It's easy to come off than Thinned "Bond G17"(one of liqud glue in Japan).
 Then, use this for weapons and armors without moving parts.
-The gross is smaller than Thinned "Bond G17"(one of liqud glue in Japan).

【Commodities　page】
Gesso or Black Gesso
or

【Paint】
Lacquer Spray or Bottle lacquer paint or acrylic paint
or

2.Wood glue thinned with water
This is so easy.

【Merit】
-Someone can get
-Someone can use easy

【Demerit】
-Drying time is a little long.

【Commodities　page】


3."Bond G17"(one of liqud glue in Japan)
This is dangerous method, it's most likely happening fire.
I wrote about this method as a archive,
However I don't recommend this.
I don't use this method now, I use other method now.
If accedents happens, it's self-responsibility.

【Merit】
-It'st hard to peel off.
-It can use for PVC pipe or plastic sheets.

【Demerit】
-"Bond G17" is japanese commodity. Then you can't get it easily.
-It needs thinner, then you must work outdoors.
-It burns easily.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
The parts will be charred in seconds.

【Commodities　page】
"Bond G17"(one of sticky glue in Japan) thined with lacquer thinner
&

-About paint
I use following paint.


You can use acrylic paint, when you use Gesso.


・About mask
In spray painting or lacquer painting, use a mask for painting.
↑フィルタ付きセット商品 ←替えフィルタ


I use "Zoukei be-su" as undercoat this time.
But it's sold only in Japan.
Substitute Gesso or Wood glue thinned with water.


Paint "Zoukei be-su" twice with a brush.
Dry it about 2 ~ 6 hours.


Dry it about 2 ~ 6 hours.


Dry it about 2 ~ 6 hours.


Paint black as undercoat color with Lacquer Spray.


Paint black as undercoat color with Lacquer Spray.


Paint black as undercoat color with Lacquer Spray.


Paint gold with Lacquer Spray.


Paint gold with Lacquer Spray.


Paint gold with Lacquer Spray.


Process Masking tape.
Stick Masking tape on a Cutting mat.


ギャクヨガは細かいところは10mm幅(左の商品)、広い所は30mm幅(右の商品)を使ってます

Mark.


I finished marking.


Cut with a Box cutter etc.


Stick Masking tape on the point you don't want to paint.


Paint silver with Lacquer Spray.


Stick Masking tape on the point you don't want to paint.


Paint silver with Lacquer Spray.


Actually, I used a Airbrush too.
If you want to make light and shade, use it.
About Airbrush is here.





●初心者にオススメ
安価なUSB充電式エアブラシ。
これ一つでエアブラシ塗装が手軽に行えます。
エアブラシ塗装を手軽に始めるならまずはこれ。


●本格的に始めるなら
Mr.カラーを作っているクレオスのエアブラシセットです。
エアブラシ塗装に必要なものが一式セットになった定番商品です。
ギャクヨガも昔使ってました。
電源はコンセント接続です。



●ギャクヨガが使っている物を使いたいなら
性能は高いですが高価です。
ホースは別途購入が必要です。



Paint gloss spray to make a gloss.



After painting
Cut out Synthetic leather.

PUストレッチレザー 生地 無地 全52色 白 黒 緑 銀系 17色 布幅130cm 50cm以上10cm単位販売 価格：179円（税込、送料別) (2019/11/10時点)

レザーストレッチニット厚手 生地 無地 計37色 赤 ピンク 黄 オレンジ 茶 紫系 20色 布幅140cm 50cm以上10cm単位販売 価格：204円（税込、送料別) (2019/11/10時点)

フェイクレザー 生地 無地 計36色 白 黒 緑 青 紫系 20色 布幅140cm 50cm以上10cm単位販売 価格：179円（税込、送料別) (2019/11/10時点)

メタルエナメル 全20色 無地 黒 白 青 紫 緑 オレンジ 赤 ピンク系 布幅135cm 50cm以上10cm単位販売 価格：204円（税込、送料別) (2019/11/10時点)

ソフトエナメル 生地 無地 42色 モノトーン、ゴールド・シルバー系 全42色 布幅130cm 50cm以上10cm単位販売 価格：191円（税込、送料別) (2019/11/10時点)

Glue with a Hot melt(glue gun).


Complete


Please watch the tutorial video too.












Please follow Twitter
Tweets by gyakuyoga

About using for business
When you use my contents for business, follow this rule.