My profile & Contact

Kantai collection -Kan Kore-
Tenryu's equipment
How to make ship part (with templates)
Vol.5 light,assembly stick



Return to Vol.4(battery part)

Attention in the work
-When you uses a thing including the thinner(Bond, lacquer thinner etc) or spray, make good ventilation.
And wear a gas mask.


-When you toast mterials etc, make good ventilation.
And don't breathe smoke, don't put smoke in your eyes.

-When you dig mterials etc with Soldering iron, make good ventilation.
And don't breathe in smoke, don't put smoke in your eyes.

-Don't use fire near the things which are easy to burn such as paint, thinner etc.

-When you finished using tools, pull an outlet.

-Read labels of materials and tools, and understand how to use.

How to make templates
Make Templates from "Kousakuyousi"(one of hard paper in Japan).
When you want to know how to make Templates, browse this page.



I finished making the Templates.


How to build
Cut material into the Templates form.
Cut out 5mm thick EVA foam.
You must use a tool for cutting out a fair circle. Details are here.
The numbers in photo is name of templates.


**********************************************************************

EVA foam is a soft material.
You can process it easily.
Another name is EVA board, EVA zote, Craft foam etc.
I usually use one called "Lion board".
"Lion board" is sold only in Japan.

Watch video.

**********************************************************************


-------------------------------------------------------------------------------------------------------
【5mm厚COSボードをキャラヌノで買う】


【COSボードを楽天で買う】

-------------------------------------------------------------------------------------------------------
【5mm厚コスプレボードをAmazonで買う】


【コスプレボードを楽天で買う】

-------------------------------------------------------------------------------------------------------

**********************************************************************

Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

When you cut, put EVA foam on Cutting mat.
Don't cut in the air, while holding by hand.
Break a b blade frequentry, if you feel sharpness of using blade became bad.
If you want to do work more speedy, use "Running fire box cutter","Blade breaker".
"Running fire box cutter" can have 6 pieces blade inside.
"Blade breaker" can break easy and speedy.


Use Art knife PRO for small ornaments etc.

**********************************************************************




Glue with a Liquid super glue.
When you use a Super glue Accelerator, Hardening speed becomes fast.
(Smoke may be generated. Don't breathe in the smoke and don't put in eyes.)


**********************************************************************


Super glue can glue a large surfaces easily.
But it can't glue a small surface such as this photo well


Then you should use a following spray.
I always use this.
Watch video.


Super glue accelerator
This can glue surfaces in several seconds.
When you use 100ml, you can make a armorset or about three weapons.
←100ml ←180ml ←420ml

About super glue
I use general liquid super glue.

**********************************************************************


Cut it into slant with a Box cutter.


Make reflection of light better.
Put a silver tape.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.
You must use a tool for cutting out a fair circle. Details are here.


Form by shaving with a Box cutter.


Cut out Clear color plastic sheets.



Glue with a Liquid super glue.


Heap with a Hot melt(glue gun).


↑ギャクヨガが愛用しているグルーガンです、口が広くてとても使いやすい!

Make a hole with a Box cutter.


Remove unnecessary parts from LED Light.


Removing was completed.


Insert.


Shine.
Remove LED Light when not in use.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.
You must use a tool for cutting out a fair circle. Details are here.


Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Hot melt(glue gun).


Remove the corner by toasting with a Lighter.(Don't breathe in the smoke, be careful about fire)


↑ギャクヨガ愛用ライター、使いやすい! ガスがなくなったらボンベで充填しましょう

Make rivets with a Hot melt(glue gun).


Cut material into the Templates form.
Cut out 10mm thick EVA foam.
You must use a tool for cutting out a fair circle. Details are here.

-------------------------------------------------------------------------------------------------------
【10mm厚COSボードをキャラヌノで買う】


【COSボードを楽天で買う】

-------------------------------------------------------------------------------------------------------
【10mm厚コスプレボードをAmazonで買う】


【コスプレボードを楽天で買う】

-------------------------------------------------------------------------------------------------------

Make a core.
Use a PVC pipe(diameter 18.0mm).
Cut a PVC pipe.
PVC pipe can be cut with a saw.
But a Pipe cutter is more better.
It can cut quickly and neatly.



This is a video of cutting method of PVC pipe, bending method, jointing method.


I finished cutting.


Glue with a Liquid super glue.


Glue Velcro with "Bond G17"(one of sticky glue in Japan) or a Hot melt(glue gun). Detailes are here.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.



Cut material into the Templates form.
Cut out 10mm thick EVA foam.
You must use a tool for cutting out a fair circle. Details are here.


Make a core.
Use a PVC pipe(diameter 18.0mm).
Cut a PVC pipe.
PVC pipe can be cut with a saw.
But a Pipe cutter is more better.
It can cut quickly and neatly.



This is a video of cutting method of PVC pipe, bending method, jointing method.


I finished cutting.
Make two.


Glue with a Liquid super glue.


To be continued vol.6(painting part)

Please
I'm making Yotube videos.
Please watch them and please subscribe my YouTube channel.
These are new videos.














着用者は友人のマロパピさん。
マロパピさんとの合作、造形部以外はマロパピさん製。
マロパピさんTwitter blog








Return to Top page