EVA foam is soft material.
You can process it easily.
Other names are EVA board, EVA zote, Craft foam etc.
Cosplayers all over the world use this.
It's sold in Amazon or AliExpress etc.

Introduction video




Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

I always use "Running fire box cutter","Blade breaker",Cutting mat.
"Blade breaker" can break the blade easily.


Use Standard art knife or Cushion grip art knife to cut small ornaments etc, too.
Standard art kinfe is for 1.5mm thickness and 3mm thickness.
Cushion grip art knife is for 5mm thickness and 10mm thickness.

●5mm厚コスプレボードを楽天で買う

コスプレボード 白5mm×660mm×500mm 価格：517円（税込、送料別) (2019/10/23時点)

コスプレボード 白5mm×660mm×1000mm 価格：990円（税込、送料別) (2019/10/23時点)

コスプレボード　白5mm×1000mm×2000mm 価格：3564円（税込、送料別) (2019/10/23時点)

コスプレボード　黒5mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：1320円（税込、送料別) (2019/10/23時点)

コスプレボード　黒5mm×1000mm×2000mm 黒だから裏塗り処理を省略出来る 価格：4180円（税込、送料別) (2019/10/23時点)

●5mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 5mm厚 白 価格：880円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 5mm厚 白 価格：1,560円（税込、送料別) (2023/5/25時点)

COSボード匠 Lサイズ 5mm厚 白 価格：5,300円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 5mm厚 黒 価格：880円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 5mm厚 黒 価格：1,560円（税込、送料別) (2023/5/25時点)

●10mm厚コスプレボードを楽天で買う

コスプレボード 白10mm×660mm×500mm 価格：880円（税込、送料別) (2019/10/23時点)

コスプレボード　白10mm×660mm×1000mm 価格：1540円（税込、送料別) (2019/10/23時点)

コスプレボード　黒10mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：2486円（税込、送料別) (2019/10/23時点)

●10mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 10mm厚 白 価格：1,400円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 10mm厚 白 価格：2,490円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 10mm厚 黒 価格：1,400円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 10mm厚 黒 価格：2,490円（税込、送料別) (2023/5/25時点)

Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)



I finished glueing.


Cut "Kousakuyousi"(one of hard paper in Japan) into a belt form.


Put "Kousakuyousi"(one of hard paper in Japan) side by side.


Paste them



"Kousakuyousi"(one of hard paper in Japan) is sold in only Japan.
It's harder than Drawing paper. The thickness is about 0.5mm.
I'm sure you can't get it.
Then, substitute various thin plastic sheets.


Cut material into the Templates form.
Cut out "Kousakuyousi"(one of hard paper in Japan).


Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)


I finished glueing.


Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)


Cut material into the Templates form.
Cut out "Kousakuyousi"(one of hard paper in Japan).


Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)


I finished glueing.


Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)


I finished glueing.


The cross section.


Paste edge of blade with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.


Reinforce the blade by applying Liquid super glue on the edge.


Make a stick part.
Use a PVC pipe(diameter 2.6cm).
Cut a PVC pipe.
PVC pipe can be cut with a saw.
But a Pipe cutter is more better.
It can cut quickly and neatly.



This is a video of cutting method of PVC pipe, bending method, jointing method.


I finished cutting.


Cut material into the Templates form.
Cut out 1.5mm or 2mm thick EVA foam.

●1.5mm厚コスプレボードを楽天で買う

コスプレボード　白1.5mm×660mm×1000mm 価格：605円（税込、送料別) (2019/10/23時点)

コスプレボード　黒1.5mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：660円（税込、送料別) (2019/10/23時点)

コスプレボードシール　白1.5mm×660mm×500mm 接着剤不要のシール接着、装飾等に 価格：594円（税込、送料別) (2019/10/23時点)

コスプレボードシール　黒1.5mm×660mm×500mm 接着剤不要のシール接着、装飾等に 価格：682円（税込、送料別) (2019/10/23時点)

●1.5mm厚コスプレボードをAmazonで買う

COSボード匠 Sサイズ 2mm厚 白 価格：620円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 2mm厚 白 価格：1,000円（税込、送料別) (2023/5/25時点)

COSボード匠 Lサイズ 2mm厚 白 価格：4,000円（税込、送料別) (2023/5/25時点)

COSボード匠 Sサイズ 2mm厚 黒 価格：620円（税込、送料別) (2023/5/25時点)

COSボード匠 Mサイズ 2mm厚 黒 価格：1,000円（税込、送料別) (2023/5/25時点)

Glue with a Liquid super glue.
When you use a Super glue Accelerator, Hardening speed becomes fast.
(Smoke may be generated. Don't breathe in the smoke and don't put in eyes.)





Super glue accelerator makes hardening time short.
It's so useful.
Watch this video.


When you use 100ml, you can make a armorset or about two, three weapons.
←100ml ←420ml


Glue with a Hot melt(glue gun).


ギャクヨガが愛用しているグルーガンです、口が広くてとても使いやすい！

I finished glueing.


Make the claw of "A".
Cut material into the Templates form.
Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


I finished glueing.


Heat it by Heat gun or Steam iron. Bend it and keep the form.
(Actually I used fire, but it's dangerous method. I recommend Heat gun or Steam iron.
If accedents happens, it's self-responsibility)



Cut out to make a hollow.


Shift the position. Glue with a Liquid super glue.


Make the claw of "B" by the same method.


Completed.


Make the claw of "C" by the same method.


Completed.


Glue with a Hot melt(glue gun).


I finished glueing.


Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 3mm thick EVA foam.





3mm厚コスプレボードを楽天で買う

コスプレボード 白3mm×660mm×500mm 価格：418円（税込、送料別) (2019/10/23時点)

コスプレボード　白3mm×660mm×1000mm 価格：693円（税込、送料別) (2019/10/23時点)

コスプレボード　白3mm×1000mm×2000mm 価格：2464円（税込、送料別) (2019/10/23時点)

コスプレボード 黒3mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：990円（税込、送料別) (2019/10/23時点)

コスプレボードシール　白3mm×660mm×500mm 接着剤不要のシール接着、装飾等に 価格：726円（税込、送料別) (2019/10/23時点)

●3mm厚コスプレボードをAmazonで買う

Glue with a Liquid super glue.


Glue with "Bond G17"(one of sticky glue in Japan).
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
(You may glue with a Liquid super glue. However "Bond G17"(one of sticky glue in Japan) is useful for the large area.)


I finished glueing.


Cut out 10mm thick EVA foam.


Glue with a Liquid super glue.


Cut out 5mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


I finished glueing.


Cut material into the Templates form.
Cut out 3mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


Cut material into the Templates form.
Cut out 3mm thick EVA foam.


Glue with a Liquid super glue.


Heap a Hot melt(glue gun) for reinforcement.


Glue with a Liquid super glue.


Make the edges smooth with a Soldering iron (Don't breathe in the smoke, be careful a burn).
Or, cut it by edged tools.
(Actually I used fire, but it's dangerous method. I recommend a Soldering iron
If accedents happens, it's self-responsibility)


Make rivets with a Hot melt(glue gun).


Draw scales.
Mark.


Heap with a Hot melt(glue gun).


Draw patterns with a Hot melt(glue gun).


Present state.



Please follow and subscribe
Please follow my Facebook & twitter!


Please subscribe my channel!


Painting
Begin painting.
Thin Wood glue with water, and paint it.
The effects are as follows.

-Color becomes well.
-It becomes hard to come off.
-Gloss comes out well.
-You can save quantity of the paint.



Paint thinned Wood glue twice or three times with a brush.
Dry it for one day.


Mix Wood glue and Flour.



Paint mixed one scales and claws.
Dry it for one day.
The surface becomes rough.


Paint gray color as undercoat color with Lacquer Spray.


Paint black color as undercoat color with Lacquer Spray.


Paint brown Bottle lacquer paint with a Airbrush.





●初心者にオススメ
安価なUSB充電式エアブラシ。
これ一つでエアブラシ塗装が手軽に行えます。
エアブラシ塗装を手軽に始めるならまずはこれ。


●本格的に始めるなら
Mr.カラーを作っているクレオスのエアブラシセットです。
エアブラシ塗装に必要なものが一式セットになった定番商品です。
ギャクヨガも昔使ってました。
電源はコンセント接続です。



●ギャクヨガが使っている物を使いたいなら
性能は高いですが高価です。
ホースは別途購入が必要です。




When you paint Bottle lacquer paint, use a paintbrush, cups, panint sticks, thinner.



Paint blue Bottle lacquer paint with a Airbrush.


Paint black Bottle lacquer paint by Drybrush painting.


Drybrush painting is easy, you can do it with a paint brush.
Read here or watch this video.


Paint white Bottle lacquer paint by Drybrush painting.


Paint silver Bottle lacquer paint with a Airbrush.


Use a spray that removes gloss to remove gloss on scales and claws..



After painting
Cut out Synthetic leather.


Glue with a Hot melt(glue gun).


Complete


Please watch the tutorial video too.














Visitor's works
【コトノカナさん Twitter】
モンスターハンタージンオウ装備&レックスライサー
どちらもギャクヨガさんを参考に作りましたヽ(・∀・)ノ
いつもお世話になっております…


Please follow Twitter
Tweets by gyakuyoga

About using for business
When you use my contents for business, follow this rule.