EVA foam is soft material.
You can process it easily.
Other names are EVA board, EVA zote, Craft foam etc.
Cosplayers all over the world use this.

Introduction video

COSボード Sサイズ(450mm×600mm) 10mm厚 白 価格：986円（税込、送料別) (2019/10/23時点)

COSボード Mサイズ(600mm×900mm) 10mm厚 白 価格：1849円（税込、送料別) (2019/10/23時点)

COSボード Lサイズ(900mm×1800mm) 10mm厚 白 価格：6274円（税込、送料別) (2019/10/23時点)

COSボード Sサイズ(450mm×600mm) 10mm厚 黒 価格：1232円（税込、送料別) (2019/10/23時点)

COSボード Mサイズ(600mm×900mm) 10mm厚 黒 価格：2353円（税込、送料別) (2019/10/23時点)

●10mm厚COSボードをキャラヌノで買う


●10mm厚コスプレボードをAmazonで買う


●10mm厚コスプレボードを楽天で買う

コスプレボード 白10mm×660mm×500mm 価格：880円（税込、送料別) (2019/10/23時点)

コスプレボード　白10mm×660mm×1000mm 価格：1540円（税込、送料別) (2019/10/23時点)

コスプレボード　黒10mm×660mm×1000mm 黒だから裏塗り処理を省略出来る 価格：2486円（税込、送料別) (2019/10/23時点)

Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

I always use "Running fire box cutter","Blade breaker",Cutting mat.
"Blade breaker" can break the blade easily.


Use Standard art knife or Cushion grip art knife to cut small ornaments etc, too.



Mark.


Cut out with a Box cutter etc.


Glue with a Hot melt(glue gun).


Glue with a Liquid super glue.
When you use a Super glue Accelerator, Hardening speed becomes fast.
(Smoke may be generated. Don't breathe in the smoke and don't put in eyes.)





Super glue can glue a large surfaces easily.
But it can't glue a small surface such as this photo well


Then you should use a following spray.
I always use this.
Watch video.


Super glue accelerator
This can glue surfaces in several seconds.
When you use 100ml, you can make a armorset or about three weapons.
←100ml ←420ml

About super glue
I use general liquid super glue.



Form by shaving with a Box cutter etc.


I finished shaving.


Remove the corner by toasting with a Lighter.(Don't breathe in the smoke, be careful about fire)


↑ギャクヨガ愛用ライター、使いやすい！ ガスがなくなったらボンベで充填しましょう

Push back of Box cutter etc before getting cold
The form becomes minus screw form when it gets cold.


Push back of Box cutter etc before getting cold
The form becomes minus screw form when it gets cold.


It got cold and hardened


Present state.


Please subscribe and follow
Please subscribe my channel!


Please follow my twitter!


Painting
Begin painting.
At first, paint undercoat on EVA foam.
The effects are as follows.

-Color becomes well.
-It becomes hard to come off.
-Gloss comes out well.
-You can save quantity of the paint.


1.Gesso
This is easy.

【Merit】
-It's usable just to paint with a paint brush.
-Gesso don't contain thinner, then you can use it in the room.
-You can use also Acrylic paint.
-There are several colors one, white black etc.

【Demerit】
-It's easy to come off than Thinned "Bond G17"(one of liqud glue in Japan).
 Then, use this for weapons and armors without moving parts.
-The gross is smaller than Thinned "Bond G17"(one of liqud glue in Japan).

【Commodities　page】
Gesso or Black Gesso
or

【Paint】
Lacquer Spray or Bottle lacquer paint or acrylic paint
or

2.Wood glue thinned with water
This is so easy.

【Merit】
-Someone can get
-Someone can use easy

【Demerit】
-Drying time is a little long.

【Commodities　page】


3."Bond G17"(one of liqud glue in Japan)
This is difficult, however it's almighty.

【Merit】
-It'st hard to peel off.
-It can use for PVC pipe or plastic sheets.

【Demerit】
-"Bond G17" is japanese commodity.
 Then you can't get it easily.
 Please use others. For example, you can substitute wood glue for it.
-You must thin it with lacquer thinner.
-It needs thinner, then you must work outdoors.
-It burns easily.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
The parts will be charred in seconds.

【Tutorial video】


【Commodities　page】
"Bond G17"(one of sticky glue in Japan) thined with lacquer thinner
&

-About paint
I use following paint.


You can use acrylic paint, when you use Gesso.



I use Gesso in this tutorial.


Paint Gesso twice or three times with a brush.
Dry it about 2 ~ 6 hours.


Paint gray color as undercoat color with Lacquer Spray.


Paint black color as undercoat color with Lacquer Spray.


Paint silver Bottle lacquer paint by Drybrush painting.


Drybrush painting is easy, you can do it with a paint brush.
Read here or watch this video.


When you paint Bottle lacquer paint, use a paintbrush,silicon cup(Use as a paint plate. It can easy to peel paints after dry.),
panint stick, thinner.



Paint rust color.
Paint brown color of Bottle lacquer paint with a paint brush.
Tap with tip of brush.


Paint orange color of Bottle lacquer paint with a paint brush.
Tap with tip of brush.


Present state.


Paint ivory color of Bottle lacquer paint with a paint brush.


Drybrush paint brown color Bottle lacquer paint with a paint brush.


After painting
Wrap a Plastic tape.


Complete






I joined interview movie in Official site of The Last Of Us.