MAIL
I have facebook.
I'm writting about new props in English.

Sengoku Basara Matsunaga Hisahide's sword
How to make Pattern paper



Infomation of materials are here

Attention in the work
-When you uses a thing including the thinner(Bond, lacquer thinner etc) or spray, make good ventilation.
And wear a gas mask.
<-I'm using this mask.

-When you toast mterials etc, make good ventilation.
And don't breathe smoke, don't put smoke in your eyes.

-When you dig mterials etc with Soldering iron, make good ventilation.
And don't breathe in smoke, don't put smoke in your eyes.

-Don't use fire near the things which are easy to burn such as paint, thinner etc.

-When you finished using tools, pull an outlet.

-Read labels of materials and tools, and understand how to use.

How to make
Make blade.
Make ground plan from "Kousakuyousi"(one of hard paper in Japan).



Cut out center of an edge.


Paste 10mm thick EVA foam with double sided tape to stand up vertical.


**********************************************************************

EVA foam is a soft material.
You can process it easily.
Another name is EVA board, EVA zote, Craft foam etc.
I usually use one called "Lion board".
"Lion board" is sold only in Japan.

Watch video.

**********************************************************************


【10mm厚ライオンボード(別名:リアラボード、ソフトボード)をAmazonで買う】
リアラボードという商品名ですがこれが俗に言うライオンボードです。
私もこの商品を使っています。


裏面がシールになってて接着剤を使わず貼り付け可能、装飾等にオススメ。


【10mm厚ライオンボード(別名:リアラボード、ソフトボード)を楽天で買う】


【10mm厚COSボードを楽天で買う】


【10mm厚COSボードをネット通販で買う】


**********************************************************************

Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

When you cut, put EVA foam on Cutting mat.
Don't cut in the air, while holding by hand.
Break a b blade frequentry, if you feel sharpness of using blade became bad.
If you want to do work more speedy, use "Running fire box cutter","Blade breaker".
"Running fire box cutter" can have 6 pieces blade inside.
"Blade breaker" can break easy and speedy.


Use Art knife PRO for small ornaments etc.

**********************************************************************


Mark center of an edge.


Paste 10mm thick EVA foam with double sided tape matching center of edge.


Make a tip.


Paste a tip.


Measure from center to end. It's width of a blade.


Cut "Kousakuyousi"(one of hard paper in Japan) to the width of edge. Cut Cut "Kousakuyousi"(one of hard paper in Japan) put on.


Mark to the form of tip.


Cut out.


Make a parts of pattern in base.
Paste Drawing paper cut proper size with Scotch tape.



Cut and paste some Drawing paper cut small.


When you make ideal form, make a fair copy from "Kousakuyousi"(one of hard paper in Japan).


Check there is no problem.


Make somewhat, and check there is no problem again.


It's OK.


Make a pattern.


Write the pattern.


Cut out part of the pattern, and it becomes a template.


Cut out "Kousakuyousi"(one of hard paper in Japan) by the template.
Stick with a Scotch tape(Sellotape) and check state.
If it's OK, it is formal.


Templates was completed.


Please
I'm making Yotube videos.
Please watch them and please subscribe my channel.
Click this↓ And Click "subscribe".



















Return to Top page