My profile

Fate/Zero
Fate/Grand Order
Berserk's armor
How to make helm (with templates)



Materials
[Materials for making templates]
-Drawing paper 10sheets
-Scotch tape(Sellotape) 3pieces
-Packaging tape(parcel tape) 1piece

[Main materials]
-EVA foam
→2mm or 1.5mm thick 100cm X 30cm
→5mm thick 100cm X 60cm
-Synthetic leather 100cm X 50cm
-Clear color plastic sheets 100cm X 40cm
-"Bond G17"(one of liqud glue in Japan) 150ml
-Liquid super glue 2pieces
-Hot melt(glue gun) 20pieces (When you use a Air duster for cooling, it's convenient)
-"Jiyujizai"(one of wire in Japan)
→6mm diameter 40cm
-Velcro 40cm

[Painting materials]
Painting method in this time
-Natural sand 100ml

Below are standart method.
1.When a undercoat is Gesso
-Gesso 100ml
-lacquer paint(Bottle lacquer paint, Lacquer Spray etc) or acrylic paint proper quantity*
-Masking tape 1piece

2.When a undercoat is Thinned "Bond G17"(one of liqud glue in Japan)
-"Bond G17"(one of liqud glue in Japan) 200ml
-lacquer thinner 200ml
-Paintbrush 1piece
-Paper cup, bowl etc 1piece
-lacquer paint(Bottle lacquer paint, Lacquer Spray etc) proper quantity*
-Masking tape 1piece

*The paiting area is written in the package, refer it. Details are here.

Materials cost
4000Yen (about 100Yen = 1dollar)

Tools
-Writing implement(Pencil,eraser,ballpoint,Magic Marker,ruler)
-Scissors
-Box cutter(Use also a "Pro blade" and a "Blade breaker")
-Cutting mat
-Hot melt(glue gun)
-Lighter
-Soldering iron and soldering iron stand
-Paint tools, such as a paintbrush
-Pliers

Convenient tools when you have
-Art knife PRO
-Heat gun
-Super glue Accelerator

Work time
20hours

Spec
-

Template data
PDF format(A4 size)

-How to print is here.
-After printing, it becomes easy to use by sticking it on Drawing paper with spray glue.
-Size:Free size
-It may not be displayed in a browser.In that case save on desktop.and open.
-Mention called "x1","x2" etc are number of cutting pieces.
(If you need both arms or both legs etc, cut the number of double.)
-Mentions of "2mm" , "5mm" etc are thickness of EVA foam.

Completion drawing


Attention in the work
-When you uses a thing including the thinner(Bond, lacquer thinner etc) or spray, make good ventilation.
And wear a gas mask.


-When you toast mterials etc, make good ventilation.
And don't breathe smoke, don't put smoke in your eyes.

-When you dig mterials etc with Soldering iron, make good ventilation.
And don't breathe in smoke, don't put smoke in your eyes.

-Don't use fire near the things which are easy to burn such as paint, thinner etc.

-When you finished using tools, pull an outlet.

-Read labels of materials and tools, and understand how to use.

How to make
Make Templates from Drawing paper.
When you make Templates of the head, use a mannequin head.
When you want to know detailed tutorial of making Templates, browse this page.





Repeat cutting and pasting.


Repeat cutting and pasting.


Repeat cutting and pasting.


Repeat cutting and pasting.


When you make a ideal from, cut open it. Use it.


Copy the edges of Templates on a material with a pen.
Cut out 5mm thick EVA foam.
Cut out 2mm or 1.5mm thick EVA foam.


**********************************************************************

EVA foam is a soft material.
You can process it easily.
Another name is EVA board, EVA zote, Craft foam etc.
I usually use one called "Lion board".
"Lion board" is sold only in Japan.

Watch video.

**********************************************************************


-------------------------------------------------------------------------------------------------------
【5mm厚COSボード】


【5mm厚コスプレボード】


楽天なら


【5mm厚ライオンボード(別名:リアラボード)】


楽天なら

-------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------
【1.5mm厚COSボード】


【1.5mm厚コスプレボード】


楽天なら


【1.5mm厚ライオンボード(別名:リアラボード)】


楽天なら

-------------------------------------------------------------------------------------------------------

**********************************************************************

Use a sharp blade. For example, "Pro Blade".
This is so sharp.
←10枚入り ←50枚入りお得パック

When you cut, put EVA foam on Cutting mat.
Don't cut in the air, while holding by hand.
Break a b blade frequentry, if you feel sharpness of using blade became bad.
If you want to do work more speedy, use "Running fire box cutter","Blade breaker".
"Running fire box cutter" can have 6 pieces blade inside.
"Blade breaker" can break easy and speedy.


Use Art knife PRO for small ornaments etc.

**********************************************************************


Glue Synthetic leather on the backside with a "Bond G17"(one of liqud glue in Japan) for reinforcement. Detailed process is here.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.




Make holes on the patterns of the Templates. Mark them with a pen.


Marking was completed.


Glue with a Liquid super glue.
When you use a Super glue Accelerator, Hardening speed becomes fast.
(Smoke may be generated. Don't breathe in the smoke and don't put in eyes.)


**********************************************************************


Super glue can glue a large surfaces easily.
But it can't glue a small surface such as this photo well


Then you should use a following spray.
I always use this.
Watch video.


Super glue accelerator
This can glue surfaces in several seconds.
When you use 100ml, you can make a armorset or about three weapons.
←100ml ←180ml ←420ml

About super glue
I use general liquid super glue.

**********************************************************************


Glue with a Liquid super glue.


Heat swelling with Lighter, and press by a finger. Swelling will be flat.

←ガス充填式ライターとガスボンベを使うとお得

Swelling became flat.


Make plate parts.


Glue with a Liquid super glue.


Cut 2mm or 1.5mm thick EVA foam thin.


Glue with a Liquid super glue.


Glueing was completed.


Dig marked pattern with a Soldering iron.(Don't breathe in the smoke and don't put in eyes)



Bend by heating with a Lighter or a Heat gun.



Glue with a Liquid super glue.


Glue with a Liquid super glue.


Reinforce by heaping a Hot melt(glue gun) on the backside of glueing places.
Glue Cloth or Synthetic leather on points with burdens.



Make the cylinder parts.
Cut out 5mm thick EVA foam.
Cut out 2mm or 1.5mm thick EVA foam.


Glue with a Liquid super glue.


Glue with a Hot melt(glue gun).


Make the front part.


Glue with a Liquid super glue.


Cut it into slant with a Box cutter.


Cutting was completed.


Glue with a Liquid super glue.


Glue with a Liquid super glue.


Glueing was completed.


Glue Velcro with "Bond G17"(one of liqud glue in Japan) or a Hot melt(glue gun). Detailes are here.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.



Remove the corner by toasting with a Lighter.(Don't breathe in the smoke and don't put in eyes)


Make the tufty part.
Paste together two Synthetic leather.
Glue with "Bond G17"(one of liqud glue in Japan).



Glueing was completed.


Cut out with a Box cutter.


Glue with a Liquid super glue.


Use a "Jiyujizai"(one of wire in Japan) of diameter 6mm.
Cut it with Pliers.
Cut it to 40cm.

←様々な太さ有り

Glue with a Liquid super glue.


Cut out 2mm or 1.5mm thick EVA foam.
Glue with a Liquid super glue.


Insert the parts when fitting.


Stick Masking tape on the point you don't want to paint.



Begin painting.
At first, paint a undercoat on EVA foam.
The effects are as follows.

-Color becomes well.
-It becomes hard to come off.
-Gloss comes out well.
-You can save quantity of the paint.

There are two methods.
-------------------------------------------------------------------------------------------
1.Gesso
This is easy.

【Merit】
-It's usable just to paint with a paint brush.
-Gesso don't contain thinner, then you can use it in the room.
-You can use also Acrylic paint.
-There are several colors one, white black etc.

【Demerit】
-It's easy to come off than Thinned "Bond G17"(one of liqud glue in Japan).
 Then, use this for weapons and armors without moving parts.
-The gross is smaller than Thinned "Bond G17"(one of liqud glue in Japan).

【Commodities page】
Gesso or Black Gesso
or

【Paint】
Lacquer Spray or Bottle lacquer paint or acrylic paint
or
-------------------------------------------------------------------------------------------
2."Bond G17"(one of liqud glue in Japan)
This is difficult, however it's almighty.

【Merit】
-It'st hard to peel off.
-It can use for PVC pipe or plastic sheets.

【Demerit】
-"Bond G17" is japanese commodity.
 Then you can't get it easily.
 Please use others. For example, you can substitute wood glue for it.
-You must thin it with lacquer thinner.
-It needs thinner, then you must work outdoors.
-It burns easily.
Don't use fire until drying, because "Bond G17" burns easily. Don' use a Lighter etc until drying.
The parts will be charred in seconds.

【Tutorial video】


【Commodities page】
"Bond G17"(one of liqud glue in Japan) thined with lacquer thinner
-for big things -for small things
-------------------------------------------------------------------------------------------
-About paint
I use following paint.


You can use acrylic paint, when you use Gesso.

-------------------------------------------------------------------------------------------

I usually use the methods mentioned above.
In this time, I paint Natural sand for making a scabrous surface.
Natural sand is one of undercoat for acrylic paint.
It's made in Liquitex Co.



Paint Natural sand twice with a brush.
Dry it about 2 ~ 6 hours.


Paint silver as undercoat color with Lacquer Spray.


Paint blue with Lacquer Spray.


Stick Masking tape on the point you don't want to paint.


Paint black with Lacquer Spray.


Paint blue with Lacquer Spray.


Actually, I used a Airbrush too.
If you want to make light and shade, use it.
About Airbrush is here.

←初心者にもオススメのセット、私も愛用してます。

Cut out Clear color plastic sheets.


Glue with a Hot melt(glue gun).


Please
I'm making Yotube videos.
Please watch them and please subscribe my YouTube channel.
These are new videos.














Dismantle state.








Visitor's works
KOITSUさん
モモンの兜のバイザー部分の型紙をどう作ったらいいのか苦戦してた時に
ギャクヨガさんのサイトのこの兜の型紙データを発見し非常に参考になりました
ありがとうございました



Return to Top page